Installing Inlay Strips
(bass drum hoops/rims)
© JamminSam. All rights reserved.
(Continued from Applying New Wrap to the Shell)
Important Disclaimer
Jammin Sam / Sam Barnard (company and individually) is not responsible for
any injury due to misuse of any tool, use of glue/adhesives, use of any
glue/adhesive removers or anything used as such, or injury due to removing or
applying drum covering. Anytime one uses a tool or product there is a chance
of injury, especially when the items are misused. Rarely has anyone ever been
hurt, but in any harmful situation, Sam Barnard (company [Jammin Sam, Sam Barnard,
Barnard Music] and individually) is not responsible for what one does with any tool
or products in attempting to complete following instructions or any other methods/
directions recommended by this company, anyone associated with Sam Barnard, or
others.
For the purposes of dispute resolution, by opening a product package from JamminSam,
you agree to be governed by the laws of the state of Arizona. It is agreed that any
legal proceedings arising out of this receipt of goods from JamminSam shall be
litigated in any court of competent jurisdiction in the state in which JamminSam
is located.
If you ordered hoop strips for the bass drum hoops, you either order small
strips to place in a cut-out groove, or enough material to cover the entire
width of the hoop. These pieces are cut to size, and if the correct measurement
was given to us, they are ready to install. All individual bass hoops (18"
or larger) need two strips (one longer, one shorter) to totally cover them. If
you ordered a strip to fit into a groove, first install the shorter length strip,
then the longer one. There should be no need for clamping the seams, just remove
the liners, press firm, then install the hoop on the bass drum (hi-bond tape
pressed down last).
If you ordered enough material to cover the entire width of the hoop (wood hoops
only), put the shorter length piece on first, then the longer one– just like the
"groove" application. But, because there is no hardware holding the
material (like the drum shells), and these pieces are more exposed to be caught on
objects, these pieces will have to be glued down. You can use any contact cement,
but for best results, we suggest "Elmer’s" regular ("Glue-All")
white glue. First, with the shorter length strip, coat the back with glue (without
the liners removed). While wet, place it down on the hoop at the desired location
(without the liners removed). Do this before the glue "sets up" so the
material can be adjusted/slid to the desired location on the hoop. Next, when the
material is centered, removed the liners and press down the tape on the wooden hoop.
If any glue is exposed on the wood (edge), use a damp cloth to remove it immediately.
Follow the same directions for the longer top piece. Allow the hoops to dry for 24
hours at room temperature before installing them on the bass drum.
Important Note:
If for some reason the inlay strips are too wide, find a sheet of medium-course
sand paper and a lid of a jar that has a flat top (the metal or plastic lid is not
raised). Windup the inlay strip tight and place in the lid (to hold the strip
tight and even). Then while holding the lid, sand one side of the inlay against
the sandpaper face up on a table until the desired width is obtained. If you have
any questions or problems just give us a call.
Special Note for Drum Wrap That Comes too Wide:
An alternative to the above trimming method (above "Note") can be used
to sand drum material (pieces for drums) that come slightly too wide (tall).
Roll the material up tight and using sandpaper w/ a block of wood, sand down from
the top (while the roll is placed on a table or floor). Sand one or both ends
until the desired size is obtained.
Caution:
Do not expose your new material to excessive heat or direct sunlight on
moderately hot days. This may cause a bubbling/expanding effect with
the material (this will not happen with chrome and satin flame finishes).
This is a typical reaction of recovery materials sold. Our materials can
be exposed to direct sunlight up to 100 degrees (90 degrees for the darker
finishes)! If you have any questions or problems do not hesitate to call.
The drum material we sell is the highest quality material available but,
if misused, even it will not stay nice with improper care.
This article continues with ...
Eyelet Installer Instructions
Thank you for choosing Jammin Sam’s drum wrap. If you have any
questions, please feel free to contact us. Click below (on the blue headings)
to read about our "Guarantee/Warrantee" and other information. We welcome
your interest in all our products on this site and hope that you will call us for a
free catalog and samples of our drum material. Thank you for spending the time
to read this article.
|
